NETGEAR Network Hardware WNDAP360 100NAS User Manual

WNDAP360_IG_3Mar2011.fm Page 1 Thursday, March 3, 2011 2:47 PM  
c. Select Configuration > System > Basic > General from the menu. Fill in  
the Access Point Name field and select your Country/Region of operation  
from the drop-down list.  
b. Connect an Ethernet cable from  
the access point to the PC (point  
A in the illustration).  
Installation Guide  
A
NETGEAR Cable  
d. Select Configuration > IP > IP Settings from the menu and configure the  
c. Securely insert the other end of  
the cable into the access point  
Ethernet port (point B in the  
illustration).  
IP settings for your network.  
e. If you use DHCP, reserve an IP address (based on the access point’s MAC  
address) on the DHCP server. You can then use that address to log in to  
the access point.  
ProSafe® Dual Band Wireless-N Access Point WNDAP360  
Ethernet  
port  
B
d. Connect the power adapter to the  
access point and verify the  
following:  
f. Select Configuration > Wireless > Basic > Wireless Settings and select  
the Turn Radio On setting.  
Package Contents  
Power. The Power LED blinks  
WNDAP360  
g. Select Configuration > Security > Profile Settings and configure security  
Unpack the box and verify the contents:  
when the access point is first  
profiles for your network.  
turned on. After a few seconds it should stay on (steady green). If after 30  
seconds the Power LED is off or is still blinking, check the connections  
and check to see if the power outlet is controlled by a wall switch that is  
turned off.  
ProSafe® Dual Band Wireless-N Access Point WNDAP360  
Straight through Category 5 Ethernet cable  
Power adapter and cord (12V, 1A)  
See the online help or the Reference Manual for full instructions.  
3. Test wireless connectivity.  
Using a PC with a wireless adapter, verify that you can establish a wireless  
connection to the access point.  
Wall mount kit  
ACTIVE. The ACTIVE LED blinks when there is network traffic.  
Installation Guide  
LAN. The LAN LED indicates LAN speeds; green for 1000 Mbps, amber  
Now that you have finished the setup, you are ready to deploy the access point  
in your network. If needed, you can reconfigure the PC you used in step 1 back  
to its original TCP/IP settings.  
Resource CD, which includes link to the Reference Manual  
for 100Mbps, and no light for 10Mbps.  
2.4G Hz (WLAN). This LED indicates 2.4 G Hz traffic.  
5 G Hz (WLAN). This LED indicates 5 G Hz traffic.  
2. Configure LAN and wireless access  
Set Up the Access Point  
Follow these instructions to set up your wireless access point. Before proceeding  
with the WNDAP360 installation, familiarize yourself with the contents of the  
Resource CD. See the Reference Manual for instructions on advanced  
configuration options.  
Deploy the Access Point  
1. Disconnect the access point and position it where you will deploy it. The best  
location is elevated such as wall or ceiling mounted, at the center of your  
wireless coverage area, and within line of sight of all mobile devices.  
a. From your PC, configure the access point Ethernet port for LAN access.  
Connect to the access point by opening your browser and entering  
http://192.168.0.100 in the address field.  
Estimated Completion Time: 3 minutes.  
2. Connect an Ethernet cable from your access point to a LAN port on your  
router, switch, or hub.  
Tip: Before mounting the access point in a high location, first set up  
and test the unit to verify wireless network connectivity.  
3. Connect the power adapter to the wireless access point and plug the power  
adapter into a power outlet. The Power and LAN LEDs should go on.  
b. A login window displays. When  
prompted, enter admin for the user  
name and password for the  
password, both in lower case  
letters.  
1. Connect the wireless access point to your computer.  
Tip: The access point supports Power over Ethernet (PoE). If you have  
a switch that provides PoE, you do not need to use the power adapter  
to power the access point. This can be especially convenient when the  
access point is installed in a high location far from a power outlet.  
a. Prepare a PC with an Ethernet adapter. If this PC is already part of your  
network, record its TCP/IP configuration settings. Configure the PC with a  
static IP address of 192.168.0.210 and 255.255.255.0 as the subnet mask.  
The access point user interface  
displays.  
 

Multiquip Projection Television GB114BW User Manual
Nady Systems Water System HM 10 User Manual
Nextar MP3 Player MA588 User Manual
Nortel Networks Switch 100 Chassis User Manual
Numark Industries DJ Equipment NS6 User Manual
Oki Printer LED Printer User Manual
Olympus Camera Lens f28 35 User Manual
ooma IP Phone 100 0201 100 User Manual
OWI Speaker System T572 User Manual
P3 International Pest Control Equipment P7906 User Manual